SAF and SAW split pillow blocks use a two-piece, cast metal housing with inch dimensions. With the included SKF bearings, seals, and related components, they provide a tailored solution to achieve maximum service life and reduce maintenance requirements for rotating equipment. These pillow blocks have been developed to be the best choice for design, quality, robustness, and cost efficiency.
| da |
165.1 mm
|
Shaft diameter |
|---|---|---|
| Da |
320 mm
|
Diameter of bearing seat |
|
G7
|
Tolerance class of bearing seat | |
| Ca |
95.809 mm
|
Width of bearing seat |
| A1 |
180.975 mm
|
Housing foot width |
| A2 |
250.825 mm
|
Width |
| H |
377.825 mm
|
Height |
| H1 |
190.5 mm
|
Centre height of bearing seat |
| H2 |
76.2 mm
|
Foot height |
| J |
min. 530.225 mm
|
Distance between attachment bolts |
| J |
max. 600.075 mm
|
Distance between attachment bolts |
| J1 |
117.475 mm
|
Distance between attachment bolts, axial |
| L |
679.45 mm
|
Length |
| N1 |
28.575 mm
|
Width of attachment bolt hole |
| S |
4.763 mm
|
Offset of locating bearing |
| R1 |
114.3 mm
|
Distance of drain plug from centre |
|---|---|---|
| R2 |
41.275 mm
|
Height of drain plug position |
| RG |
3/4-14 NPT
|
Thread of drain hole |
| PG |
1/4-18 NPT
|
Thread for grease fitting in cap |
| Dynamic load rating | C |
1 237 kN
|
|---|---|---|
| Static load rating | C0 |
1 560 kN
|
| Fatigue load limit | Pu |
140 kN
|
| Reference speed |
1 800 r/min
|
|
| Limiting speed |
2 600 r/min
|
|
| Limiting value | e |
0.26
|
| Calculation factor | Y1 |
2.6
|
| Calculation factor | Y2 |
3.9
|
| Calculation factor | Y0 |
2.5
|
| P60 |
234 kN
|
Safe load at 60° load angle |
|---|---|---|
| P90 |
140 kN
|
Safe load at 90° load angle |
| P120 |
84.5 kN
|
Safe load at 120° load angle |
| P150 |
75.6 kN
|
Safe load at 150° load angle |
| P180 |
89 kN
|
Safe load at 180° load angle |
| Pa |
57.8 kN
|
Safe load, axial |
| Housing material |
Cast iron
|
| Paint, corrosion protection |
Paint – in accordance with ISO 12944-2, corrosivity category C2
|
| Mass |
137 kg
|
| Cap bolt |
3/4-10 UNC x 6
|
|
| Number of cap bolts |
4
|
|
| Recommended tightening torque for cap bolts |
203.373 N·m
|
|
| SAE grade of cap bolt |
5
|
|
| Eye bolt |
3/8-16 UNC
|
|
| Number of eye bolts |
2
|
|
| Recommended diameter of attachment bolts | G |
25.4 mm
|
| Required locating (stabilizing) ring | ||
| Number of required locating rings |
1
|
| Initial grease fill, 20% |
2 145.492 g
|
|
| Initial grease fill, 40% |
3 460.91 g
|
|
| Oil level | h |
60.325 mm
|
Reviews
There are no reviews yet.